<bdo id='cjdls'><sup id='cjdls'><div id='cjdls'><bdo id='cjdls'></bdo></div></sup></bdo>

?挖掘機配重004A

2021-04-13 10:35:25

次

詳細介紹：

　　1.選取和安裝

　　叉車配重的質量、質心位置、后懸量由整車總體布置給定，其中平衡重質量的選取主要考慮叉車滿載堆垛和滿載行駛時的縱向穩定性。平衡重的質量直接影響到叉車前、后平衡的保護系數，是決定叉車保護系數的主要參數。當平衡重的總質量G定下來后，即以后橋為基準，根據車架上平衡重的裝配形式，準確明確平衡重的安裝尺寸。叉車尾架上部外側有2個倒置的V形懸掛塊，將平衡重用2條螺栓固定在其上。

　　2.通風孔

　　由于熱平衡是叉車很重要的參數，散熱性能不好很容易造成發動機冷卻水水溫過高現象，影響叉車整車性能。因此，平衡重通風孔的位置、風道與氣流導向就顯得很重要。通風孔開的越高越大越利于散熱;通風孔到散熱器之間采用圓角過渡，以利于氣流導向，提散熱性能。

　　3.離去角

　　配重下端的離去角也很重要，該角度主要是為了分開上、下坡時平衡重下端與地面摩擦，理論上離去角與具體車型的大爬(pa)坡角相等。平衡重下端切除點的位置要根據具體車型的大爬(pa)坡度、平衡重的后懸量來明確。

沃爾沃裝載機配重